18 Watt stout with Hot switch.
This is not a kit, it is a parts listing from my project build.
|
| Back to
library page |
| Qty |
Description
of part |
| 1 |
Suitable Chassis
of your choice - I do not stock a small Stout chassis. |
|
Back panel parts |
| 1 |
rotary
impedance selector switch |
|
1 |
Knob of your choice |
|
2 |
#11 jacks speaker jacks |
| 1 |
12 Foot Power cord |
|
1 |
Fender style Fuse
holders for mains |
| 1 |
main Slo-blo fuse 1 amp |
|
1 |
Spst Carling power switch |
|
Front panel parts |
| 1 |
LED Lamp assembly |
| 1 |
180 Ohm
LED current limiting resistor |
|
2 |
Knobs of your choice |
|
2 |
pots 2 x 500KA |
|
1 |
12A input jack |
| 1 |
SPST mini toggle
switch - relay only |
|
Top chassis parts |
|
4 |
9 pin
tube sockets that fits your chassis |
| 2 |
12AX7
pre amp tubes |
| 2 |
EL84
power tubes |
| 2 |
EL84 spring clips |
|
1 |
8 pin tube socket that fits your chassis - rectifier tube |
|
1 |
5Y3 Rectifier Tube |
|
1 |
Sovtek tube spring retainer - rectifier tube |
| 1 |
18 Watt power tranny with 5 volt tap |
| 1 |
18 Watt output tranny with 4, 8 and 16 ohm taps |
| Off board 1/2 watt
resistors |
| 2 |
100 ohm - heater center tap |
| 1 |
100K - pots |
| 2 |
8.2K - El84 grid stoppers |
| 1 |
1M - input jack |
| Off board misc. |
| 1 |
125C3A
choke |
|
1 |
40x20x20x20 filter cap |
|
1 |
40x20x20x20 cap clamp |
| 5 ft |
Each Red, Black, White,
Green
20GA Solid core wire or cloth wire |
| 5 ft |
18 Gauge Heater
wire or cloth wire |
| 5 ft |
Mini shielded cable if
shielding is needed. |
| 6 |
#8 Ring terminals |
| 6 inches |
Heat shrink
tubing |
| 1 |
6 Lug terminal strip |
| Assortment of #4,
#6 and #8 screws, nuts and washers, depending on what you are mounting. Get
20 of each to have on hand. |
|
Circuit board 1/2 watt
resistors |
| 1 |
820 OHM |
| 2 |
2.2K |
| 1 |
47K |
| 4 |
100K |
| 5 |
47OK |
|
Circuit board 3 watt
resistors |
| 1 |
4.7K |
| 1 |
10K |
| 2 |
1K |
|
Circuit board 10 watt
resistors |
| 1 |
130 Ohm or 150 ohm |
| Circuit board capacitors |
| 1 |
.0047 Mallory 150 - 400 volt
or higher |
| 2 |
.01 Mallory 150 - 400 volt or
higher |
| 4 |
.022 Mallory 150 - 400 volt or
higher |
| 1 |
.68/250V |
| 1 |
47uf/100v cathode cap |
| Circuit board
misc. |
| 4 |
1/4" Nylon standoffs |
| 4 |
#8 x 5/8" screws |
| 4 |
#8 Nuts |
| 1 |
1/8" Thick circuit board
x 7.25 inches
long |
| 44 |
Turret lugs - 52 if you are
doing relay switching |
| On board Relay stuff |
| 1 |
Relay socket |
| 1 |
5 volt signal switching relay |
| 1 |
1N4001 or 1N4007 Diode |
| Relay power
supply board |
| 1 |
Bridge #1 - See my web catalog |
| 2 |
4700uf/16V caps |
| 1 |
1/2 watt dropping resistor -
100 ohm will work |
| 1 |
1/8" Thick circuit board
x 1.5" wide x 3"
long |
| 7 |
Turret lugs |
